No i deer

Ok thank you sir.. I will have too source some nuts first..!! This will save messing around pillar or fully bedding hopefully 👍

Hi MPM1 Out of intrest how did you come to the conclusion the screw was too long and how is shortening the screws a few threads going to help..?? Thanks NID

Thank you. I will get around to it over the next few days 👍 I will compare the screws before I take any threads off just incase the other ones I have are shorter.

I have a spare set of remmy action screws I could try.. thanks for that tip MPM1 👍

KRG whiskey 3 stock is a aluminium vblock chassis.. It may need some pillars or the full works.. My remmy action must be much stiffer as I've never had that issue with my 6.5x47 in the AICS stock or it has the perfect fit

I've added some weight to my f open KRG whiskey 3 stock so it helps with the torquing. If I had a 1.250 parallel barrel I'd be still under ok. I think my fairly recent barrel is a tad heavier than my older barrel being it's about 1 inch at the muzzle and still 1lb and a half under the limit. A spur mount would be an expensive weight add on 😅. I'd rather spend the money on more bullets and powder 👍. The spur mount would stiffen up my Borden timberline action would be a good thing because if I over tighten a fraction it affects the bolt running smoothly.. back the action screw off a fag paper and it runs sweet again.. I've been looking at torque wrenches of late so I know what I'm torquing it too.. Bicycle wrench sets look the best option so far

I've seen other mounts like spur mounts etc but wasn't aware of a unimount pops. Like I said my knowledge on this stuff is limited that's why I asked 😉. Seen stuff that was of no real intrest as it is expensive aesthetics goodies 😁

Thanks for replies.. TBH my favourite rings are the optilock sako and tikka rings. A solid fixing too the action with no farty little screws holding on the pic rail. Bolted strait too the action with recoil lugs and tapered dovetail with the inserts. Too much of the fancy stuff around that just cost alot of money. I've never had an issue with optilocks.

I was looking through dolphin precision engineering site and noticed these unimounts.. I'm not big into scope rings and mounts and had no I deer what a unimount is..!! Can someone care to enlighten me 🤙

Are you still selling this rifle 🤔

It's got a silly thread size

I would of liked it but I'm not buying another gun I can't shoot 🙄

It would be a shame to split that combo

Once the neck turner is set it will take a few seconds a case to uniform the necks..!! It really is so simple and quick 👍

I thought I heard it was around 600 shots, I'm sure where I heard it from these people get 3 barrels done at a time 😳😬😁

I won't John I'm just trying to be optimistic 👍🤙

🤞😉

Just in time for the European f class championships at Bisley 😁😎. Followed by the Topgun comp 😋

I didn't see the mitsi veneers 🤔

6.5x47 with 142gr and N160

It's nearing the time for me to get a 338 lap mag then 😁

Looks like you have everything you need 🤣. You could of bought alot of factory ammo from what you've spent on kit 😉.

The cases will soon stretch.. 2 or 3 thousanths on firing and around the same resizing them..

Yeah it was he loved it.. He said it was pressure shooting in the tight timings He has plans for a cheytac and the whole build I think but sourcing the parts is the hard bit.

A club mate who is a member of the FCSA who shot at last years 50 cal world championships at Raton also had the oppertunity to shoot in the KO2M. He was lent the gun and the ammo by some generous american team which was a 375 cheytac.. I think he was 11th overall.. He engaged the first three ranges but didn't connect with the 4th range..