Swarovski1 Posted October 24, 2016 Report Share Posted October 24, 2016 I did a cof at last 1000yd day with my 284's first time out.i used a untested 52.5gr rs60 180gr hybrid load.ive found now the cases with shiney spot on are tightish closing bolt after prepping.i haven't measured the case head yet but i guess the bolt sides and ejector is a squeeze.my question is can I take off 2 or 3 thousandths off the head to sort this. Link to comment Share on other sites More sharing options...
andybrock Posted October 24, 2016 Report Share Posted October 24, 2016 Have you full length resized them properly? Link to comment Share on other sites More sharing options...
justin credible Posted October 24, 2016 Report Share Posted October 24, 2016 If cases are tight on the bolt close, it normally means the shoulders need knocking back 2 thou. Link to comment Share on other sites More sharing options...
Swarovski1 Posted October 24, 2016 Author Report Share Posted October 24, 2016 After measuring everything I went on YouTube to see how t3 bolt comes apart lol.did that.picked the tightest case then slackened the locking ring off turned the die down and resized.tried chambering it.felt better.did that process a few more times until I could feel the slightest resistance on the last bit of the bolt shutting.resized a few more and all was good.retigthened lock screw and resized all again and reseated primers.never had a tight bolt before probaly coz I use to oversize the cases.i might make a reloader yet .i have loaded enough for a cof sunday and some of loaded rounds are tightish.will they be ok to shoot or should I pull them and reload them again.thanks for replies. Swaro Link to comment Share on other sites More sharing options...
Re-Pete Posted October 25, 2016 Report Share Posted October 25, 2016 If you can close the bolt, and the charge won't result in excess pressure, they'll be OK to shoot..............how do you know the loaded rounds are tightish? Surely not by chambering one, (other than on the range with the rifle pointing at the target)? That way madness lies...................... RePete Link to comment Share on other sites More sharing options...
Swarovski1 Posted October 25, 2016 Author Report Share Posted October 25, 2016 Hi pete.i chambered some of the loaded rounds that had ejector marks on last night.never fired any.cheers swaro Link to comment Share on other sites More sharing options...
DaveT Posted October 25, 2016 Report Share Posted October 25, 2016 Your post indicates two issues... Ejector marks usually signify excessive pressures...sometimes residual sizing lube can contaminate the chamber and prevent the neck end of the round gripping the chamber and causing the whole case to slam back into the boltface rather than the rear simply stretching back ....this can produce EJ marks. Your headspace sizing is covered above by other posts. I would deal with the Ejector mark issue as a priority. Link to comment Share on other sites More sharing options...
Brillo Posted October 25, 2016 Report Share Posted October 25, 2016 Neil, If your chamber has a competition throat and the COAL is therefore close to mine with the hybrids (3.218") the previous load you used is right is right on the edge of high pressure. The ejector marks qualify this. I suggest F/L sizing as you've done and dropping back the charge by 0.5 grains. Link to comment Share on other sites More sharing options...
Elwood Posted October 25, 2016 Report Share Posted October 25, 2016 Try doing load development! Just because someone said their load is 52.5 grains of RL17 they might have been using a slow batch and you might have a fast batch, that's why we do load development. As Brillo says, 52.5 grains is right on the edge and RL17 has a reputation of not showing pressure and then spiking very quickly. Now it might be accurate with that powder charge but your cases will be fubarred in six firings or less. Your load was never going to blow the action up, but you owe it to yourself and the people you shoot around to do things properly. Link to comment Share on other sites More sharing options...
Swarovski1 Posted October 25, 2016 Author Report Share Posted October 25, 2016 I was watching for pressures every shot.i had maybe about 12 cases that had shiney spots on out of 36 shots.bolt lift was ok.no force to open it.i did step down 0.5grs too 52grs and they are perfect.52.5grs gave the 180gr hybrids 2915fps.52grs gives 2884 fps from 26 inch tube.thats plenty fast enough for me Link to comment Share on other sites More sharing options...
Swarovski1 Posted October 25, 2016 Author Report Share Posted October 25, 2016 I was watching for pressures every shot.i had maybe about 12 cases that had shiney spots on out of 36 shots.bolt lift was ok.no force to open it.i have stepped down 0.5grs too 52grs and they are perfect.52.5grs gave the 180gr hybrids 2915fps.52grs gives 2884 fps from 26 inch tube.thats plenty fast enough for me.i will be switching to H4831sc when rs60 is gone to use up 4 tubs of it.got some more loaded ready to test up from 55gr load which I didnt chrony,55.6gr i hear is an accuracy load then up to 56.2grs.see how 55.6grs goes first.55gr accuracy looked good.was down to me.i didn't chrony but 54.5grs was doing 2640fps.too slow.55grs probaly doesn't make 2700 fps.thats the trouble with RS60. It gives so much speed it's hard not to want to use it.i you had followed my thread my 284 you would of seen some of my load development target's Elwood, ive did some research and I new 52,5grs would be near max, I just hapoened to have more of this load developement load made up at different seating depths than the 52gr load so I shortened them to the shortest oal and made a few more enough for zero and a cof. Link to comment Share on other sites More sharing options...
Swarovski1 Posted October 27, 2016 Author Report Share Posted October 27, 2016 When I had a 30 06 I bought some whetherby cases that were to tight in the bolt face with the ejector.i skimmed a few thousandths of the head of the case and they were fine after.trying to close the bolt they would shave off the edge of the case Link to comment Share on other sites More sharing options...
Elwood Posted October 27, 2016 Report Share Posted October 27, 2016 t.i used a untested 52.5gr rs60 180gr hybrid load..My reply was based on your information. Anyway hopefully your problem has been diagnosed before you trash the primer pockets on your cases. Link to comment Share on other sites More sharing options...
Lukas_K Posted November 1, 2016 Report Share Posted November 1, 2016 Also note that a tight-headspaced round (tight-ish on closing) results in slightly higher pressure as compared to a rightly full-sized one (same load). Your rounds will lose a few fps in velocity and may need a click or two more at distance than what you´ve previously observed. Re-working your load development from scratch helps to take out any variables Link to comment Share on other sites More sharing options...
Swarovski1 Posted November 1, 2016 Author Report Share Posted November 1, 2016 All sorted chaps.thanks for replies.my load developement loads that shot demon was Virgin brass so I can't see much has changed there . certainly hope not.would be a shame if they don't shoot like this anymore Link to comment Share on other sites More sharing options...
Recommended Posts
Archived
This topic is now archived and is closed to further replies.