-
Posts
1,427 -
Joined
Content Type
Profiles
Forums
Events
Articles
Posts posted by One on top of two
-
-
What did you re-torque them to Neil ?
if you can print groups like that. Do you think your gain much .
-
-
Also when you do your NRA assessment for the SCC it is valid for 4 or 5 yrs as opposed to the standard yearly as an affiliated club member
-
18 minutes ago, Popsbengo said:
The point of the SCC is to provide an approved 'passport' for shooters wishing to shoot away from their club ranges. I would be surprised if a commercial range would just let someone with an FAC rock up and start shooting without some competence checks.
Your location is not identified, where are you based?
⬆️ this
-
-
How old is it ?
-
General Discussion
Chat about anything on or off topic
that’s what it says at the top of the page 😁👍🖕🏻
-
-
The link takes you straight to it. If not it your browser settings
-
-
-
Quick zero
150 m
For the record I have turned the settings down in daylight mode to suit my eyes , it’s really bright and clear in real world settings .
-
2 hours ago, terryh said:
A simple gauge is a fired 223 case, pop the rf bullet into the case nose first and measure the loa.
Dirty pikeys 😷
-
You might also want to try one of the little hornady case gauges
your be surprised how much difference there can be in the case rim , which is chngeing the head space by as much as 4 thou on some cases .
there only about £20
it’s all about the little things .
-
The old 40 grn eley subs were the best imo that’s all I ever used along with eley HV that were the same bullet just a bit more punch .
what I did Neil was start around 15 Inch pounds for BOTH action screws … 10 shot group then
16 inch pounds ….10 shot group
you know where is going , and I ended up at 22 inch pounds
I think the max torque is 28 inch pounds for both screws .
I think it does make a difference be it a small one .
Give it a go
-
neil .
on both of my old 452 s
torque setting is 22 inch pounds for both action screws
-
I had a go this morning , it was a shocking 100% pilot error.
I have a Kahles K525i sitting here doing nowt at the min . im going to put it on the rimmy and see what occurs.
-
1 minute ago, Montey said:
Would it make a difference that there are two licence holders at the address both license holders shot gun and FAC does then mean 30kg can be held?
NO .
if you want more , you need an explosive licenseno ifs ….no buts
like I said , contact your FEO or Firearms department
that’s one of there jobs .
-
Most don’t . But it all goes FIZZ … POP….BANG ….WHOOOOSH haha.
think of the poor fire-persons standing outside your house try to put it out .
You can hold more but.... you would need an explosives license and of course meet the conditions of that license
👍👍👍
-
15Kg of ALL smokeless powder on premises that’s including shotgun carts .
when I was doing lots of clay shooting on the circuit we used to chip in ( 3 of us ) and buy a pallet load which had 26K
thay had to be split in at least 2 different locations, and no not 13k under the stairs and the other 13k in the garage , as in spilt and taken away .
Depending on the carts I think it was between 10-13k of shells contains around 15 KG of smokeless powder
FEO was very strict about it and still are.
double check with your Firearms dept
-
Me too mate …. One in ..one out
-
2 hours ago, No i deer said:
Lucky you 🙃
you know what you need Neil ......😉 you need someone who's got a spare V3 kicking about. with Area 419 bits and bobs .
-
just set the transition weight to around 1.2 👍
I would say mine is about the same
-
My V4 turned up this morning . All set up and ready to go 👍
Autotrickler V4
in Handloading
Posted
Go on there website and change prices to £ from $ add your postage and it will tell you exactly 👍