Aaron

still available gun is at a local rfd here in northern ireland and stock is at home 

Selling my tikka t3 stainless 

22” barrel 1-12 twist (I believe)

Atec mod with extra baffle

new 5 shot mag along with original 3 shot

Around 300 shots all have been factory ppu 55 grain soft point 

extended rearward rail but can be turned the opposite direction if needed I had it like this to aid in better eye relief with certain nv and thermal scopes 

also have a grs bifrost stock for it or can be sold separately 

gun currently in my local dealer so no problems doing rfd 

looking £600 for rifle 

grs stock I’m looking £250 

Tikka t3 light stainless 

a tec mod with extra baffle

seen less than 300 rounds mostly 55grain soft point and accounted for many a fox 

grs bifrost stock 

extended pic rail for better eye relief when using nv or thermal 

based in Northern Ireland but no problem with sending it through RFD 

scope not included but can be if a deal breaker 

Only selling as putting my vermin control days behind me will upload or can send more detailed pics later 

£900 for rifle and mod 

This Still available??

Just purchased a new chassis after running a mdt lss gen 1 for close to 6 years on my rimfire

Recently getting into prs matches so bought a xrs for the longer forend and going to run a acra rail

Don't want to go crazy with prices certainly not paying near 800 for a mdt 

What's people's opinion 

Sold to a friend on mates rates 🤦‍♂️

Mike the friend I shoot with wants it apparently so giving him a few days to get the money sorted, if it falls through I'll send ya a pm 

Think it's actually a mdt grip on it 

Selling my mdt chassis for the cz455 black in colour 

Mill spec buffer tube

Houge grip

Real magpul butt stock

Medium clip on riser 

One off top rail (3d printed) 

Picatinny rail section at front and rear 

£350+ postage 

Belfast based if anyone fancy ftf 

Woukd you be interested in selling the chassis? 

15 hours ago, srvet said:

How have you worked up to the load? 3800fps with a 55g bullet sounds spicy! Presumably you have worked up to this from a lower powder charge. Are there any pressure signs? Might be worth posting some pictures of the case heads from fired cases. 

Yes chum worked up to that load and was the best results out of the loads,a  fellow shooter who shoots the same rifle etc runs it similar with fantastic results he did warn me it's little  over recommended amount but most companies underrate there max load 

Cases etc look fine but I'll post pics tomorrow for second opinion 

Firstly hope everyone had a lovely Xmas,  I managed to get to the range to test out some of my first batch of reloading for the 22_250 

Went with serria 55gr pills one a soft point the other match king tipped and there a boat tail, 36.4g of n150 and federal primers getting in around 3800fps

Soft points shot really well considering I made them 😂😂😂 the other not so good was getting 2 inch groups, not sure if that's because there a longer bullet and if that has anything to do with pressure on powder inside the case answers below please 😂😂😂

Anyway what would be my best step to take next, is it play with seating depth?? And is there a easy way to figure that out I planned on using my mag for length then knocking them back to where I am currently seated but not sure how big of a jump back I would go 

Pic of my best group of the day 

Note to self please check UK varminting prior to spending 600 on a arken 

Firstly just want to say I've looked for a wanted section on the forum but can't find it so understand if this gets removed 

I'm looking ideally a krg xray for my tikka 22-250 might consider something else my shooting is 70%hunting the rest at the club 

I've currently a grs bifrost on my rig so if someone is interested in trading plus cash your way let me know 

Again apologies if this is not the place to post 

Long long shot but is this still available 

If it doesn't sell I'll have it