Jump to content
UKV - The Place for Precision Rifle Enthusiasts

No i deer

Members
  • Content count

    1,890
  • Joined

  • Last visited

Everything posted by No i deer

  1. No i deer

    6.5CM RS62 next steps in load dev

    Dasherman bushed my remmy firing pin 👍
  2. No i deer

    300 WSM - Powder recomedation

    I will probaly go down this road at some point if I get a second f open gun.
  3. No i deer

    Murom primers required Derby

    As were on primers I loaded some ammo by mistake with BR2'S instead of muroms so I thought I'd just use them up rather than pull them.. Both loads were identical bar the primers... The BR2 load averaged about 25fps faster than the muroms.
  4. No i deer

    Murom primers required Derby

    I'm not familiar with the sr muroms but I have some to try from Brillo. I've used quite a few lr muroms and they are a fraction bigger and ideal when the cases have been well used.. seating the muroms in well used brass can be like seating primers in new brass 🤩. A shooting mate had his Barrett 98b bolt face gas cut with a federal gold magnum primer.. he had a new bolt fitted and I think it happened again 🙄 It was either not seated fully, a faulty primer pocket or faulty primers..
  5. No i deer

    Murom primers required Derby

    I'm sure there's plenty of dealers in Derby but of the illegal white powdery stuff mainly 😁
  6. No i deer

    7 saum in AW Mag

    Off the top of my head I'd say no.. AI mag is about 2.9 inches internal.. I think my saum loaded with a 184gr hybrid is 3.1 inches. Mine run in a 300wm magazine and I've put a spacer at the back so the cartridge sit more forward
  7. No i deer

    Bullet Jump

    I will checkout these MME bullets 👍
  8. No i deer

    Bullet Jump

    According to Hornady there eldm bullets are the best out there with there AMP jackets and new tip that doesn't deform with top bc doplar radar proven 😁. I've used the 180gr ELDM's in my saum and 284 there very accurate. Had 3 suspected blow ups with the 180s in my tiring saum barrel. I batch weigh and measure sort the 180s but only batch weigh the 162gr ELDX's for hunting. In all fairness there pretty consistant.. I've not used jlk's but the 7mm 184gr hybrids are about the most consistant bullet I've used too date, I've gotta box of 7mm 183gr smks the measure and weigh very consistant, not got around to trying them yet Recently got the 7mm 162gr ELDX's working in my 284 very nicely. The new A tip bullets are ment to be the best of the best with a bc to go with the new aluminium tip. I'm yet to try them as I've too many 184gr hybrids to use up first and these A tips are a quid each retail 😳. If these bullets start dominating the competitions we my have no choice but to use them to be competitive. I know some have been experimenting with them before the lockdown started.. No feed back as yet, I'm talking about the 30 cal 230gr A tips in the 300wsm.. Not sure if the 7mm 190s have made it across the pond yet.. From what I've read the 190s won't suit my freebore anyway as my saum is throated for 184gr hybrids. Not sure about the tip being added after is a bad thing as it does uniform the from end of the bullets, some of the meplats can be irregular as baldie describes.. I point mine so they are somewhat improved, they could be trimmed then pointed but something I've not got around to doing thus far. I would of thought the meplat/tip is really important as this part doesn't get scarred from the rifling grooves that steers the bullet.. I don't know what the perfect bullet is but there is a variety of good ones out there now.
  9. No i deer

    Bullet Jump

    I've wondered for a while now why Berger don't make bullets with ballistic tips.. I asked that question on accurate shooter and the only reply was checkout articles that Bryan litz has done but I've not come across that particular subject yet. I do point my 7mm hybrids I use for f class as do most. The tipped bullets do seem to have a higher BC than non tipped.
  10. Thanks. I'm sure I have a set that came with the original remmy stock that was taken off even before I seen it when it armalon built it. I think the ones on my AICS stock stay in the stock when I undo them I think.. It's been a while since I've had them apart. Cheers NID
  11. No i deer

    7 saum powder choice

    This is DrT's British record plot sheet where he scored a stunning 100/14 from 1000yds at the British championships. Vbull is 0.5 moa or 5 inches
  12. Out of curiosity would i need new action screws cut to fit this stock if my remmy action is fitted to an AICS stock..??
  13. No i deer

    Leather knife sheath

    Here you go lindajanebayliss@yahoo.co.uk Atb NID
  14. No i deer

    Leather knife sheath

    I sent Mel a pm and they do sheaths..!! If your not a user of pigeon watch I could get a contact number 👍
  15. No i deer

    Leather knife sheath

    Look on pigeon watch there is somebody who makes leather bullet pouches bolt pouches etc etc.. I'm pretty sure they could..!! Look for mel 3b
  16. No i deer

    Bullet Jump

    Thanks Al 👍
  17. Selling this used Parkerhale/versapod type pod as it's not what I wanted.. I've not used it but there is some paint missing where it folds.. £80 inc postage
  18. No i deer

    Bullet Jump

    This is where the hybrid was a compromise between the 2 bullet types apparently but I'm not sure if its 5 thousanths sensitive.. I've not measured throat wear on my 1 in 8.25 saum barrel since I developed the load or checked if the accuracy has deteriorated.. It served me well at the Brits and a league match after so I've no need to want to check it... My option for a sierra f open bullet is the 183 but it's the vld type so it's in the sensitive type unlike the 180gr smks, I've not tried either. The 180gr smks could do well with the long jump explained in the blog. I'm not sure the same as you pops why.. Laurie may explain things if he sees this thread. Somewhere along the line I got mixed up on comparator measurement for my 6.5x47 with 139gr scenars.. it's done 2000 shots and throat has grown.. Once I found the I'd miss measured I gradually moved the bullet out and out and found it still likes the same measurement as it did 1900 shots ago.. I think there is some theory on the time the bullet spends in the barrel and the bullet leaving the barrel at the optimum for the harmonics.. It may not be to do with the bullet jump as we think of it as but to do with its position shortening or lengthening the time the bullet spends in the barrel 🤔. I've not got enough time to find all these things out 🤣😂
  19. No i deer

    6.5x47 and 130gr ELDM's

    Anybody using these bullets in there 47. I feel like a change and step down a little as I've always used 140's. RS62 or N150 is what powder I have. Ive got a handful of RS60 I could try too.. what is the better powder for the 130 grainers..?? as my barrels done over 2000 shots using RS60 doesn't worry me.. I've another barrel ready... Cheers NID
  20. No i deer

    6.5x47 and 130gr ELDM's

    Ok thanks.. If you find out the exact powder grainage can you post it please.
  21. No i deer

    6.5x47 and 130gr ELDM's

    How many grains of N160 Scooby..??
  22. No i deer

    6.5x47 and 130gr ELDM's

    Thanks Dave 👍
  23. No i deer

    Bullet Jump

    I was thinking of my 7mm saum that's throated for 184gr hybrids set around 10 thousanths jump. Another 50 or 60 jump will put the bullet back in the donut area on the case I expect...
×

Important Information

By using this site, you agree to our Terms of Use and Privacy Policy